Another night shift on the car (from 22h45 to 00h30). And got some goals archived!
First task was to drill holes on the nosecone to attach the grill to it. Using the dremmel and a 1mmØ drill bit, punched 6 holes on the nosecone. Cut 6 bits of steel wire 7cm long and bent them in a U shape. Then it was just putting one "leg" through the hole, the other through the outside of the cut hole and twisting it together. Bellow a detail of one twisted inside and the grill attached. Later on I'll get to paint the wires...
Back on the car, attached the two bolts that I had left drying last Monday night. Before bolting them down, put some Nural 50 on them. Then removed the ones I did Monday to add Nural 50.
Afterwards, attached the wingstays to the uprights. This task consists of tightening 3 bolts, having each one 2 spring-washers and 2 nuts that hold onto the upright and to the stay, effectively ensuring that not only the bolt doesn't come out of the upright but also that the distance to the tire is correct.
This took me around one hour. The first one was hardest because I was trying to figure out how to reach the nuts to tighten them, so I spent 40m on it. The second one was a lot faster to get done; experience is priceless! The picture shows the upright on the front left wheel.
Doing these night shifts not only got the car build going again as also are giving me a morale boost. Very happy with this!
Build diary for my first kit car: an Aries Locoblade (http://www.ariesmotorsport.com/) that I will be building in Portugal for the next months (or years).
Wednesday, February 15, 2012
Monday, February 13, 2012
Refurbishing Bolts and Preparing Grill
Spaz had alerted me to the fact that the paint should be dry by now. And he was right! ;)
After three weekends in a row where other stuff got in the way and I couldn't work on the car, I was really frustrated. So, today I did a bit of work between 22h30 and 00h10. I hope the noise did not bother anyone (since there are 3 stores between the one I was working in and the first with apartments).
When I assembled the front brakes, the bolts that hold the calipers against the uprights were not reconditioned. They were quite rusty but I bolted them anyway. This has been in the back of my mind as something I should not have done. So, started by taking out a bolt on each side and scrub it with the driller and a steel scrub tip. After that, stuck them on a piece of cardboard and painted them black. After the paint dried, I bolted them back and took the other two. This was when I took the "before and after" picture below.
Scrubbed and painted the 2nd set of bolts and left them to dry.
While the paint on the first set of bolts was drying, I looked into fitting the front grill on the nosecone. Steve had told me how he usually does it, but when I asked I had already cutted the nosecone hole and Steve's way was no longer possible. So I was thinking about marking some spots to drill holes and fix the grill with plastic straps, as I believe MK does.
With the dremmel, cut the fixing feet off the grill, so now it sits perfectly on the nosecone. Did not get around to drill the holes, but in a way it was better. The idea that the plastic straps could get cut by the fiberglass was not conforting. And in the mean time I decided to use a bit of steel wire to tie the grill, also using holes. I can later paint the wire black and all. Something to do next time.
It was great to be back on the car!
After three weekends in a row where other stuff got in the way and I couldn't work on the car, I was really frustrated. So, today I did a bit of work between 22h30 and 00h10. I hope the noise did not bother anyone (since there are 3 stores between the one I was working in and the first with apartments).
When I assembled the front brakes, the bolts that hold the calipers against the uprights were not reconditioned. They were quite rusty but I bolted them anyway. This has been in the back of my mind as something I should not have done. So, started by taking out a bolt on each side and scrub it with the driller and a steel scrub tip. After that, stuck them on a piece of cardboard and painted them black. After the paint dried, I bolted them back and took the other two. This was when I took the "before and after" picture below.
Scrubbed and painted the 2nd set of bolts and left them to dry.
While the paint on the first set of bolts was drying, I looked into fitting the front grill on the nosecone. Steve had told me how he usually does it, but when I asked I had already cutted the nosecone hole and Steve's way was no longer possible. So I was thinking about marking some spots to drill holes and fix the grill with plastic straps, as I believe MK does.
With the dremmel, cut the fixing feet off the grill, so now it sits perfectly on the nosecone. Did not get around to drill the holes, but in a way it was better. The idea that the plastic straps could get cut by the fiberglass was not conforting. And in the mean time I decided to use a bit of steel wire to tie the grill, also using holes. I can later paint the wire black and all. Something to do next time.
It was great to be back on the car!
Sunday, January 22, 2012
Painting Wing Stays
The small amount of time I had this Sunday was spent drilling and preparing the wing stays for painting.
First used a 6mmØ drillbit to get the holes for support bolts. I had marked the spots when the stays were on the car, so it was an easy job.
After that I was going to use some sandpaper on the stays but then went the lazy route and used a steel scrub on the dremmel and cleaned the surface rust and other stuff on the stays.
Gave them a first coat of black spray, taking care not to spray on the area that will be glued to the underside of the wings; if the glue holds to paint, it will not stay long. Will be spraying further layers during the week.
Nothing worth taking pictures of.
First used a 6mmØ drillbit to get the holes for support bolts. I had marked the spots when the stays were on the car, so it was an easy job.
After that I was going to use some sandpaper on the stays but then went the lazy route and used a steel scrub on the dremmel and cleaned the surface rust and other stuff on the stays.
Gave them a first coat of black spray, taking care not to spray on the area that will be glued to the underside of the wings; if the glue holds to paint, it will not stay long. Will be spraying further layers during the week.
Nothing worth taking pictures of.
Sunday, January 15, 2012
Second Wing Stay Done!
My task for today was to bend and trim the second wing stay and prepare both to be painted. Doing a task for the second time seems a lot easier than on the first attempt. So, got the second stay bent, trimmed and adjusted in half the time it took me for the first one. I was amazed at how fast it went and how similar (although it doesn't seem so in the picture) between stays the bents came out.
Didn't drill the holes in them nor sanded the metal preparing for the paint. Will try to do that during the week, o a night. It would be nice if I could assemble the stays on the car next weekend and spend my time doing something else, like wiring the dashboard...
Didn't drill the holes in them nor sanded the metal preparing for the paint. Will try to do that during the week, o a night. It would be nice if I could assemble the stays on the car next weekend and spend my time doing something else, like wiring the dashboard...
Sunday, January 8, 2012
Cycle Wing Test Fit
Took with me the cycle wings to test fit. The plan was to test fit the right one, get it done and then bend the left stay. As usual, things took a lot longer than expected.
To trial fit the wing, I had to cut the excess metal strip from the stay. Around 5cm had to go. This meant using the dremmel with a cutting disk. It was one of those few times where I regret being to tight to buy an angle grinder... Almost one hour later, had both arms of that stay trimmed and could test fit the cycle wing. The front arm was spot on. The rear arm had the first bent too tight. After unbending it a bit and adjusting the 2nd bend accordingly, had a satisfactory result.
Time to clean, pack and go home. The other stay will have to wait for next week...
To trial fit the wing, I had to cut the excess metal strip from the stay. Around 5cm had to go. This meant using the dremmel with a cutting disk. It was one of those few times where I regret being to tight to buy an angle grinder... Almost one hour later, had both arms of that stay trimmed and could test fit the cycle wing. The front arm was spot on. The rear arm had the first bent too tight. After unbending it a bit and adjusting the 2nd bend accordingly, had a satisfactory result.
Time to clean, pack and go home. The other stay will have to wait for next week...
Thursday, December 22, 2011
Steering Wheel and Wing Stays
Kind of childish, but I had to get the steering wheel on. Attached the steering wheel boss, tightened the nut and fitted the horn wires through an hole. Then bolted the wheel directly on the boss. When checking the boxes to store them, found fitting instructions that stated that I should have placed an adapter plate between the boss and the wheel. Undid it all and tried to fit the plate. It wouldn't fit for anything. Bent the part just trying to get it all to fit. A waste of time. Threw the plate back on the box and bolted the steering wheel directly on the boss again. Unfortunately, the steering wheel bolts were a bit "soft" and the allen key destroyed the inside of one. The bad thing was that the bolt was half-way in. Had to use pliers to undo it. And scratched the wheel. Oh, well... Where will I find a replacement bolt like that?
The wife and kid showed up. The kid was all happy playing with the steering wheel and it was picture time (trying to steer and use the pedals at the same time, probably not the best driving position). Then a neighbour showed up for some chat and I ended up packing and going home.
Next steps will be to bend the other wing stay, trim the edges, drill, paint and get them on the car so that I can close the brake circuit. Also put the engine airbox and the exhaust pipes. Finally, assemble the battery, charge it and wire in the ignition key. That will allow me to start the engine and see how it goes. Also need to check what I need to put the drivers seat in (bolts and nuts, I guess) so that I can later on drive the thing.
On a side note, saw on the locostbuilders forum that a MK Indy builder had a fireblade engine with the original airbox fitted and just had to make a small cut on the bonnet. That validates my decision to use the original airbox.
Grabbed a wing stay and read very carefully the instructions provided by Steve from Aries about how to bend them to suit my wheel size. He said on his message I should take my time and do this carefully, checking how it looks, to be sure it gets properly done. Using two pieces of wood from the crate where the car came, I bent the two stays from the (front) right wheel. I have to say that bending that iron plate is pretty hard! I still feel my arms tired. But in the end I have that stay bent. The instructions stated that I should dry fit the wing to check it but I had the wings at home.
Next steps will be to bend the other wing stay, trim the edges, drill, paint and get them on the car so that I can close the brake circuit. Also put the engine airbox and the exhaust pipes. Finally, assemble the battery, charge it and wire in the ignition key. That will allow me to start the engine and see how it goes. Also need to check what I need to put the drivers seat in (bolts and nuts, I guess) so that I can later on drive the thing.
On a side note, saw on the locostbuilders forum that a MK Indy builder had a fireblade engine with the original airbox fitted and just had to make a small cut on the bonnet. That validates my decision to use the original airbox.
Sunday, December 18, 2011
On The Floor!
Time to put the car on the floor, since I need that to bend the wing stays and then to, well, try to make it work and move around!
Fitted the wheels all round, hand-tightening the nuts. Then placed the jack in the front chassis, under the radiator. With it full up couldn't reach the chassis, so I placed some wood under and jacked the car up. Always careful not to get under the car (in case it suddenly fell), removed the stays and jacked it down. The rear was harder, since the suitable chassis rails were too high. So, jacked on the side and dropped the stay height one "hole". Jacked down, went to the other side, jacked up, dropped 2 "holes", jacked down, repeat to drop 2 holes, change side, repeat to remove stay, move side, remove stay. Now... my... arms... hurt...
Then went around tightening the wheel nuts, since now the wheels did not turn when more force was applied. Well... The car would start to roll a bit, but my boot under the wheel would make it stay put. Placed a couple of wood blocks under the rear wheels to hold the car in place, since it still does not have breaks. Need to take care of that soon...
The car is a bit lower than the Mazda MX5 currently sitting next to it... It will be fun!
Then I went for the steering wheel boss. Noticed I had forgotten the nut at home (I carried it to the hardware store to get the correct fitting for it's size, to be able to tighten it). But since the wires for the horn were not long enough to get inside the boss, spent some time (and wire) making extensions. I'm feeling a lot more confident working with the electrics now, which makes me very happy!
Next time will be following Steve's wonderful and detailed instructions on how to bend the wing stays so that I can then paint them, fit them on the car and after that close the break fluid circuit.
Fitted the wheels all round, hand-tightening the nuts. Then placed the jack in the front chassis, under the radiator. With it full up couldn't reach the chassis, so I placed some wood under and jacked the car up. Always careful not to get under the car (in case it suddenly fell), removed the stays and jacked it down. The rear was harder, since the suitable chassis rails were too high. So, jacked on the side and dropped the stay height one "hole". Jacked down, went to the other side, jacked up, dropped 2 "holes", jacked down, repeat to drop 2 holes, change side, repeat to remove stay, move side, remove stay. Now... my... arms... hurt...
Then went around tightening the wheel nuts, since now the wheels did not turn when more force was applied. Well... The car would start to roll a bit, but my boot under the wheel would make it stay put. Placed a couple of wood blocks under the rear wheels to hold the car in place, since it still does not have breaks. Need to take care of that soon...
The car is a bit lower than the Mazda MX5 currently sitting next to it... It will be fun!
Then I went for the steering wheel boss. Noticed I had forgotten the nut at home (I carried it to the hardware store to get the correct fitting for it's size, to be able to tighten it). But since the wires for the horn were not long enough to get inside the boss, spent some time (and wire) making extensions. I'm feeling a lot more confident working with the electrics now, which makes me very happy!
Next time will be following Steve's wonderful and detailed instructions on how to bend the wing stays so that I can then paint them, fit them on the car and after that close the break fluid circuit.
Subscribe to:
Posts (Atom)










