Saturday, April 7, 2012

IT LIVES!!! (Second "1st Start" Successful)

Woke up early and went with 2 bottles of Coke to the gas station to get more fuel. Came back with 4 litres of it. Down on the car, started by following advice given by my fellow builder Iain and other people on locostbuilders forum. So, went around the electric circuit ensuring all earths were correctly connected to the chassis. Connected the rear earth bundle, that was still to be done. Also connected a cable from the battery negative to the chassis. Then, grabbed some tape and went around isolating all terminals that I crimped and don't have a "rubber hood". Also wrote down on my wiring diagram all cables that are connected and those still to be done. Easier to keep track of them this way.

Next, I connected the Digidash to the cables, disconnected the power from the fuel pump and took some time to configure the thing. I had calculated all the needed data during the week, so I just had to feed it. It was easy, although it took a bit. Now I see Km/h.

Since the car has no breaks, jacked the rear of the car up again. This time, left the stands under it, to save me time for next times. Dumped one bottle of gas on the tank, then placed the bottle on the engine bay and placed the exit pipe from the fuel pump inside it. Connected the pump power and turned the key one notch, to get the pump going. No fuel coming out of it... Grabbed the 2nd bottle, dumped a bit of fuel on the tank and then disconnected the in pipe and placed it inside the 2nd bottle. Had to see the fuel move from one bottle to the other. Turned the key again, the fuel wouldn't move. "Shot pump", I thought. With the pump still "clacking" away, started checking the pipes. The exit blew air. The bleed one blew air. The intake didn't seem to suck. When I placed that pipe inside the bottle again, I don't know what happened, but suddenly the  fuel started to move from one bottle to the other!

With the excitement, turned the key into "start" instead of off, heard the "clack" from previous weekend and everything went dark. Disconnected and reconnected the battery negative cable, connected both pump pipes to the fuel line and carbs and dumped all the gas on the tank. Sat on the drivers side and rotated by hand the prop, just to be sure it rotated. Then, turned the key one notch, pressed the clutch down, key to start and there goes the starter engine trying to fire up the car!!! But it didn't start.

Out of the car, checked that there was a fuel smell coming out of the carbs. They were leaking to the floor. But everything else looked OK. Disconnected the power from the fuel pump, the coil leads from the sparks and sat on the car again, to make the engine spin a bit and move oil around. After some spinning, topped up the cooling circuit and reconnected the leads. Still with the pump off, tried to start the car. This time, while the starter was trying to fire it, it crossed my mind that I should press the throttle... Did so and the engine fired up! And revved so much I got scared and let it stall. (I need to drill another hole on the peddle to make it less sensitive).

Out of the car, thought "just a bit can't hurt", reconnected the pump's power, sat on the car, turned the engine on, fired it up and kept it running for a bit (probably just one minute). It would start to stall as soon as I lifted the foot from the throttle, but it did run. And it made LOTS of noise! Should connect the pan to the exhaust.

HAPPY!!! Got out of the car, topped up the refrigeration fluid again. Cleaned the leaked fuel and a bit of oil that leaked from where I connected the pickup pipe for the oil pressure sensor (probably didn't tighten it enough). Unplugged the fuel pump again, disconnected the battery and started to clean and pack. Had to call it a day.

The picture bellow shows from where the carbs leaked. Not sure if it was from what seems like nipples or if it was from behind them. Only leaked from carbs 3 and 4. I'm afraid that it's some perished rubber seal and that I'll have to take the carbs apart to replace it all. The section with a different colour/light is where the leak happened. The arrow points to one of the nipples. But as I said before, it might be leaking from behind the nipples. The fuel made a puddle on top of the gearbox and then dribbled to the floor near the prop.
Next? Tomorrow will take the wife to film it. I want some footage, she wants to see it running!
Then, work out the rear firewall, the dash, seats, breaks... I want to be able to drive it, even if just a bit inside the garage! Oh! And maybe figure out what to shortfuse to get the engine starting without the clutch down...

Saturday, March 31, 2012

First "First Start" Attempt - Fail

Today was my first "first start" attempt. I was pretty convinced it wouldn't start first time, but was hoping to be wrong. In the morning bought 2 litres of super 95 to put on the tank.

First task was connecting the Digidash looms to the car's main loom. It was quite easy, although I haven't connected the lights related ones (but then, I don't have lights yet). Then I connected the battery and tried to turn the key from off to on. The Digidash sprung to life and the fuel pump started to pump (quite loudly, actually). I turned it all off immediately and went to get the wife, that wanted to film the attempt.

Back with the wife, the kid and a friend, I poured the 2 litres on the tank, jacked up the rear wheels (brakes still don't work) and we attempted the first start. It failed. Eventually the wife and kid went back outside for him to ride his bike, the friend stayed with me trying to figure it out.

* The battery reads on the multimeter 12,48v either standing or with the Digidash and pump working;
* The pump makes loads of noise but there is no fuel going on the carbs. We disconnected the pipe that goes from pump to carbs and it was blowing (not sucking) air, but no fuel was coming out. My friend believes I need to put more petrol on the tank, that the circuit is full of air and not able to prime itself;
* When we turn the key to start the engine, there is a "click" coming from somewhere near the engine (ignition module? rectifier?) and then everything turns off. Like if a fuse had blown. And only after waiting some minutes we can attempt turning it on again. We don't hear the starter engine trying to fire the car up.

My friend had to go away, I stayed behind cleaning and packing up and came back home.

And as I was writing the above, it struck me!!! I can't start a bike engine if it is in gear without the clutch down. Could it be from that? I believe the car is in some gear since I tried to put it in gear when I was bolting down the diff. And I've tried to take it out of gear but unsuccessfully, it seems. Next time, with more fuel, I'll try it again.

Next tasks... Disconnect the pump and take some time to configure the Digidash with the tank empty so that it learns what an empty tank is. Confirm what dials and buttons I'll have on my dash, make up my mind as how to place them and then cut the dash. Fit the magnets on the prop shaft and craft a support for the speed sensor. Trim, drill and rivet the rear firewall so that I can then put in the seats and belts. Prime the brake system. Oh! And try to start the engine again... Lots to choose from!

Trying to start the car, but it just "click"'s
From HappyBlade

The Digidash powers up and acts like a Xmas tree!
From HappyBlade

Wednesday, March 28, 2012

Differential Oil

Yesterday I finished crimping all the terminals on the Digidash cables. Did the crimping while watching two episodes of "Wheeler's Dealers". With this, I can now connect the Digidash to the loom and, after powering up the car, check some readings (namely if the car is in neutral or not).

Today went for an hour and a half on the car (from 23h00 to 00h30). Spent it all using a 5cl syringe to push 1 litre of oil inside the diff (see previous post, can't open the correct plug so pushing the oil through the breather hole). While doing this boring task, my head was occupied for a bit with calculations. 100cl... 5cl syringe... 200 "shots"... I now have blisters in two fingers. But job is done! No pictures, who would want to see this?

Next? Getting some gas and try to fire up the engine? Maybe...

Saturday, March 24, 2012

More Electrics

Got one hour and a half on the car. I had been planing this bit and had all lined up to make it worth. Or so I thought. Rushed to open the diff bolt and pour the oil inside. Unfortunately, I don't have the strength for it and the alan key I used ate a bit of the plug inside. One member of the locostbuilders.co.uk forum said that, due to his lack of access to the plug, filled his diff with a syringe, through the breather hole. So I decided not to loose any more time with the plug and do that too! I have a 5cl syringe at home, it will take a while but it's just once...

Fitted the battery in the car (but didn't plug it to the loom). The bracket I fabricated is a nice fit to prevent it from moving sideways. But on acceleration/braking, it will move a bit. I need to come up with some additional restraining, probably will use some straps for that. But will have to think it over, I want it to look nice and be safe.

Next work was done on the dash wiring again. Plugged the hazards and lights relays on the loom. Then also crimped terminals and plugged the ignition key thing on the loom. It's nice that the key has some additional terminals to connect cables for other feeds. I might use it for a lighter, to connect the phone charger or GPS to.
Last task, completed later at home, was to crimp terminals on digidash's cables to connect them to the car's loom. I need to buy more terminals but crimped all those not related to lights (since I'm not installing those right now).

Next time on the car will probably seem me filling the diff with a syringe, syphoning gas from the tin top (I'm cheap, don't want to shell out 10€ for a 5L jerrycan) into it, jacking up the rear axle and trying to start the car. The start might be delayed to a weekend, the wife want's to be filming...

Tuesday, March 13, 2012

Battery, Fluids and More Electrics

Had some time away to prepare for an event. I got that off my back this morning. Since I took the whole day as vacation, spent some time after lunch on the car (how I missed it!).

On the locostbuilders forum, there were two "Engine started for the 1st time!" threads last weekend. That made me want even more to start mine. So I'm really considering some change of plans: try to start the car within 2 weeks, even without a dash nor bled brakes (will jack up the rear axle). Just for the kicks of hearing it rev. Then I'll get it moving.

With this in mind, first task was to assemble the battery. Spent loads of time careful reading all instructions and mustering courage to deal with the sulphuric acid (all those warning are scary!). Properly protected (eyeware and gloves), Followed instructions to open the battery, pour the acid inside, prepare securely the acid bottle and funnel to be disposed and finally seal the battery. Had to use the rubber mallet to convince the acid bottles to open on the funnel and also to make the sealing cap fit.
It was odd to hear the acid fizzling inside, even after sealing the battery. Left the battery there, will charge it at home, so that I can monitor it. Should buy a voltmeter first, to be able to control charge.

Then, I looked into putting cooling liquid and diff oil in. Went around looking where to pour diff oil through. It wasn't obvious so I left that for later and took a picture to ask. Quickly got the answer.
Filled the expansion tank with cooling liquid but only some of it went away through the pipes. Will have to ask about this later on, don't know if I need to have the engine (and water pump) running for the liquid to move around and allow me to pour the remaining quantity.
The last work was on the dash wiring. Spent again loads of time looking at the Digidash cables, the look section that connects to the digidash loom, the schematics, ... Procrastinating... Finally inserted the 3 fuses on the fuse box and placed connectors on all car loom wires. Later will put the connectors on the Digidash loom.
Lets see if I can start the car soon, I bet it would make me feel quite happy!

Wednesday, February 22, 2012

Indicator Light Switch

We have a saying in Portugal: "As a donkey looking to a palace". That's me looking at dash electrics!

Spent almost two hours on the car tonight (22h40 to 00h20). The focus was on dash electrics, having as a goal to wire up the digidash and minimum components to be able to initialize the Digidash ROM and turn the car on. But only managed to put the lights relay on the fuse box and wire up the indicator light switch. Wiring up the switch required creating some extensions since the loom's wires were not long enough. Usually people don't put a stalk, put some buttons on the dash, and for that it would work.
In between, tested the scuttle on the car to see how much space I had for the indicator light switch. It's always great to put some panels on the car because it really does look a lot better!

Let's hope that my next session can get me closer to being able to connect the Digidash.

Saturday, February 18, 2012

Finished Brake and Fuel Lines, Airbox and Exhaust

Almost 5 hours today, interrupted by a long lunch. And many small bits got done!

I've been saying that only the brake fluid line was not finished but actually the fuel line was not completely done either. So today I attached the filler cap on the tank. The bodywork is missing but I plan to drive the car a bit without bodywork fitted, so it's wonderful!
Next task was to bend the small copper pipes to close the frontal brake circuit, possible since I attached the wingstays. Bending the pipes by hand, to fit the tight curves, was actually easier than I anticipated. This job was quickly done.
I had the idea of cleaning the engine. Someone told me I shouldn't do it because the grease and dirt prevented it from rusting. I forgot about the idea. But then, things don't rust in the garage space so the idea came back again. Grabbed a cloth and some petrol and started to clean the engine case, rubbing the dirt off. It was being too much work and sometimes I feel I make up these tasks to postpone starting up the car... Quickly abandoned the idea again and went on to attach the airbox to the car.

My initial idea with the airbox was to attach it with the intake pipes turned down to the interior of the car. Then cut the tubes a bit and link them to a scoop I would fabricate on top of the rad. But when I fitted the airbox that way, the intake trumpets on the engine did not slide adequately inside the airbox. Turned it the other way around to make it all fit nicely but it's temporary... I need to make my initial idea work so that I have less to cut on the bonnet.

After the lunch break, the only task accomplished was to bolt on the exhaust header. It was harder than I anticipated mainly because I was working alone. Had to tie one end of the exhaust tube (after the 4-to-1) to the chassis so that it would stay level with what I needed. then another piece of rope to tie the header part to the chassis to help me sustain the weight. After some wiggling and pushing, managed to get all tubes on the engine holes and bolt everything down. Two bolts were playing hard to tighten but I placed some grease on the threads and it slid a lot better. The wonderful look of the exhaust is not visible yet since I did not unwrap it, to prevent scratches and the likes. Will unwrap it before starting the engine.
Next task will be dash electrics or assembling the battery. And I have to go buy oil for the diff, the brake circuit, refrigeration fluid, fuses and some bolts...